Lenze PLC Designer ApplicationTemplate (PLC Designer R3- Manual do Utilizador Página 79
- Página / 177
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Lenze · ApplicationTemplate · 1.3 EN - 04/2013 79
Architecture: The ApplicationTemplate in detail
State machine
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
9.3.3 The state transitions in detail
The "Init" status is reached immediately after mains switching/device reset.
• The module application executes the initialisation. After the initialisation phase, the state
machine is to be set to the "Ready" status by setting the xEnableInitToReady input.
• The following input conditions must be met so that the respective state transition is reached:
Number State transition Condition
1"Init""Ready" • SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Ready); and
• State transition is enabled by the module application
(xEnableInitToReady input = TRUE)
Note: When this method is passed through by every machine module (MM) during
the initialisation phase, all MMs are in the "Ready" status.
2"Ready"
"Manual"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Manual); and
• State transition is to be enabled by the module application in every subordinated
machine module (xDisableReadyToManual input = FALSE)
3"Ready"
"Service"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Service); and
• State transition is enabled by the module application
(xDisableReadyToService input = FALSE)
4"Ready"
"Automatic"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Automatic); and
• State transition is enabled by the module application
(xDisableReadyToAutomatic input = FALSE)
5...7 "Ready"
"Mode(1...2)"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Mode(1...2));and
• State transition is enabled by the module application:
(xDisableReadyToMode(1...2) input = FALSE)
8"Manual"
"Ready"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Ready); and
• Enable of the state transition by the module application
(xDisableManualToReady input = FALSE)
9"Service"
"Ready"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Ready); and
• State transition is enabled by the module application
(xDisableServiceToReady input = FALSE)
10 "Automatic"
"Ready"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Ready); and
• State transition is enabled by the module application
(xDisableAutomaticToReady input = FALSE)
11 ... 13 "Mode 1...2"
"Ready"
• SetState request by the master
baseChannelSetNominalState(MM_Address:= 0,
eState:=L_EATP_SMStates.Ready); and
• State transition is enabled by the module application:
(xDisableMode(1...2)ToReady input = FALSE)
- PLC Designer 1
- Contents 2
- Pictograph and signal word! 10
- About this documentation 11
- Danger! 12
- Requirements 13
- ( 110) 15
- 4.3.2 Machine modules (MM) 18
- 4.3.6 State machine 21
- 4.3.7 Error handling 22
- Note! 33
- State machine 35
- State machine ( 21) 36
- ( 119) 36
- [8-4] Example: App1 64
- 8.11 Online change 68
- Vis.diPieces := 4711; 72
- ( 127) 73
- 9.3 State machine 77
- State machine 80
- 9.4 Default coupling 83
- 9.9 Error handling 92
- 9.9.1 Defining errors 92
- 9.9.3 Acknowledging errors 93
- ÊTRUE. The 94
- ( 124) 94
- 9.10 Triggering errors 95
- How to write the CSV file: 96
- 9.13 Logbook 97
- 9.14 Module diagnostics 97
- 9.15 Multitasking 98
- 9.16 Consistent data transfer 99
- 9.17 Internal Control 101
- How to proceed: 105
- 11.2.1 L_EATP_Application 115
- 11.2.2 L_EATP_CriticalSection 117
- 11.2.4 L_EATP_ErrorSet 119
- 11.2.4.2 Acknowledging errors 120
- 11.2.5 L_EATP_Module 121
- 11.2.5.1 Base() 121
- 11.2.6 RegisterACD() 122
- 11.2.7 setCompIDAndVersion() 122
- 11.2.8 L_EATP_ModuleDiag 123
- 11.2.10 L_EATP_ModulRelations 125
- 11.2.11 L_EATP_SMAccess 126
- 11.3 2_Structs_Types 127
- 11.3.1 L_EATP_ACD_Base 127
- 11.3.2 L_EATP_BaseChannel 128
- 11.3.3 L_EATP_ErrorList 128
- 11.3.4 L_EATP_ErrorListEntry 128
- 11.3.5 L_EATP_MM_Address 129
- 11.3.6 L_EATP_MVis 129
- 11.3.7 L_EATP_scBase 129
- 11.4 3_Enums 129
- 11.4.2 L_EATP_SMStates 130
- Appendix 131
- How to proceed: 155
- Select Copy Empty 156
- Insert Empty Module 156
- )(('%$ 176
- 109 87654321 177
Manuais e produtos relacionados com Software Lenze PLC Designer ApplicationTemplate (PLC Designer R3-
(270 páginas)
Software Lenze 8400 motec Manual do Utilizador
(518 páginas)
(518 páginas)
Software Lenze i700 Manual do Utilizador
(338 páginas)
(338 páginas)
Software Lenze 8400 TopLine Manual do Utilizador
(176 páginas)
(176 páginas)
Software Lenze 8400 StateLine Manual do Utilizador
(103 páginas)
(103 páginas)
Software Lenze 8400 HighLine Manual do Utilizador
(157 páginas)
(157 páginas)
Software Lenze 8400 BaseLine C Manual do Utilizador
(342 páginas)
(342 páginas)
Software Lenze 8400 BaseLine D Manual do Utilizador
(260 páginas)
(260 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais