Lenze Drive PLC Developer Studio 9300 Servo PLC (V8.x) Manual do Utilizador descarregar pdf (Página 116)

9300 Servo PLC

Appendix

3−14

9300 Servo PLC EN 5.0

Fault message RemedyCauseDescription

No.

RemedyCauseDescription

Display

x061 CE0 Automation interface (AIF) communication

error

Faulty transfer of control commands via AIF.  Plug in the communication

module/keypad XT firmly, screw down, if

necessary.

 Switch off monitoring (C0126 = 3).

x062 CE1 Communication error on the process data

input object CAN1_IN

CAN1_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/1, if necessary.

 Switch off monitoring (C0591 = 3).

x063 CE2 Communication error on the process data

input object CAN2_IN

CAN2_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/2, if necessary.

 Switch off monitoring (C0592 = 3).

x064 CE3 Communication error on the process data

input object CAN3_IN

CAN3_IN object receives faulty data or

communication is interrupted.

 Check wiring at X4.

 Check sender.

 Increase monitoring time under

C0357/3, if necessary.

 Switch off monitoring (C0593 = 3).

x065 CE4 BUS−OFF state of system bus (CAN) The controller has received too many faulty

telegrams via the system bus (CAN) and has

disconnected from the bus.

 Check wiring at X4: Is the bus correctly

terminated?

 Check shield connection of the cables.

 Check PE connection.

 Check bus load, reduce the baud rate if

necessary. (Observe the cable length!)

 Switch off the monitoring (C0595 = 3).

x066 CE5 Time−out of system bus (CAN)

(communication error of gateway function)

For remote parameterisation (C0370,

C0371) via system bus (CAN):

 Slave does not respond.

 Communication monitoring time has

been exceeded.

 Check wiring of system bus (CAN).

 Check CAN bus configuration.

0070 U15 Undervoltage of internal 15 V voltage supply Check voltage supply.

x071 CCR System fault

Strong interference on the control cables Control cables must be shielded.

Ground or earth loops in wiring  Check wiring.

 Check PE connection.

After fault correction: completely

deenergise the device (switch off 24 V

supply, discharge DC bus)!

0072 PR1 Checksum error in parameter set 1

CAUTION: The Lenze setting is loaded

automatically!

 Fault when loading a parameter set.

 Interruption while transmitting the

parameter set via keypad.

 Set the required parameters and store

them under C0003 = 1.

 As to PLC devices, check the use of

pointers.

The stored parameters are incompatible

with the loaded software version.

Store the parameter set under C0003 = 1

first to allow for a faults reset.

0074 PEr Program error Error in the program flow Send the parameter set (on floppy

disk/CD−ROM) with a detailed description of

the problem to Lenze.

After troubleshooting: Deenergise the

device completely (disconnect 24 V

supply, discharge DC bus)!

0075 PR0 Error in parameter set.

The operating system software has been

updated.

Storage of the Lenze setting C0003 = 1.

After troubleshooting: Deenergise the

device completely (disconnect 24 V

supply, discharge DC bus)!

0079 PI Fault during parameter initialisation  An error has been detected during

parameter set transfer between two

controllers.

 Parameter set does not match the

controller, e.g. when data were

transmitted from a controller with more

performance to a controller with less

performance.

 Correct parameter set.

 Check code initialisation values.

After fault correction: completely

deenergise the device (switch off 24 V

supply, discharge DC bus)!

0080 PR6 Too many user codes Reduce the number of user codes.

x: 0 = TRIP, 1 = Message, 2 = Warning, 3 = FAIL−QSP

1 2 ... 111 112 113 114 115 116 117 118 119 120 121 ... 166 167

Comentários a estes Manuais

Sem comentários

Lenze Drive PLC Developer Studio 9300 Servo PLC (V8.x) Manual do Utilizador Página 116

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Lenze Drive PLC Developer Studio 9300 Servo PLC (V8.x)