Lenze DSD Manual do Utilizador Página 148
- Página / 496
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
7Applications
7.12 Belt conveyors for unit loads
148
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
7.12.2.6 Angle of tilt
Application with a slope (slide)
For the angle of tilt, only a positive value (slope) can be entered. However, you can dimension an ap-
plication with a slope by specifying a negative speed. If the application is moving on a slope with
negative speed, it goes backwards.
Procedure:
• Enter the value of the slope into the Angle of tilt input field.
• Enter the value with a negative sign into the Speed input field.
7.12.2.7 Coefficient of friction belt/bearing
7.12.2.8 Coefficient of friction belt/supporting rollers
7.12.2.9 Velocity
7.12.2.10 Mass of the payload
Symbol Description
β Angle of tilt (gradient)
• The value can be entered in degrees or as a percentage.
• The max. angle of tilt as a first approximation is: arctan
β ≥ arctan(μ
L
)
(static friction between load and belt).
Symbol Description
μ
Gdn
Coefficient of friction between the belt and the supporting surface
• Value can be entered directly or selected from the "Physical coefficients" table.
Coefficient of friction for rolls
Symbol Description
μ
aux
Coefficient of friction between the supporting rolls and the belt
•If μ
aux
= 0, the friction by the supporting rolls is disregarded.
• Value can be entered directly or selected from the "Physical coefficients" table.
Coefficient of friction for rolls
Symbol Description
v Speed of the belt
• Value is entered in the Motion dimensioning step.
Symbol Description
m
L
Mass of payload
• Value is entered in the Motion dimensioning step.
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Manuais e produtos relacionados com Software Lenze DSD
Software Lenze Engineer v2.21 Manual do Utilizador
(312 páginas)
(312 páginas)
Software Lenze PLC Designer ApplicationTemplate (PLC Designer R3- Manual do Utilizador
(177 páginas)
(177 páginas)
(270 páginas)
Software Lenze 8400 motec Manual do Utilizador
(518 páginas)
(518 páginas)
Software Lenze i700 Manual do Utilizador
(338 páginas)
(338 páginas)
Software Lenze 8400 TopLine Manual do Utilizador
(176 páginas)
(176 páginas)
Software Lenze 8400 StateLine Manual do Utilizador
(103 páginas)
(103 páginas)
Software Lenze 8400 HighLine Manual do Utilizador
(157 páginas)
(157 páginas)
Software Lenze 8400 BaseLine C Manual do Utilizador
(342 páginas)
(342 páginas)
Software Lenze 8400 BaseLine D Manual do Utilizador
(260 páginas)
(260 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais