Lenze 9400 Manual do Utilizador descarregar pdf (Página 936)

Index

936 Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

CAN status DIP switch (C00348) 771

CAN SYNC application cycle (C01130) 835

CAN SYNC Rx identifier (C00367) 775

CAN sync transmission cycle time (C00369) 775

CAN SYNC Tx identifier (C00368) 775

CAN telegram and error counter (C00360) 774

CAN TPDO counter (C00343) 769

CAN TPDO1 mask byte x (C00311) 764

CAN TPDO2 mask byte x (C00312) 765

CAN TPDO3 mask byte x (C00313) 765

CAN TPDO4 mask byte x (C00314) 766

CAN TPDOx cycle time (C00356) 773

CAN TPDOx delay time (C00324) 768

CAN TPDOx identifier (C00320) 766

CAN TPDOx Tx mode (C00322) 767

CAN/EPL device type (C219) 760

Capacitor temperature (C00068) 738

Change Cam Data Point M (C02926) 908

Change Cam Data Point X (C02924) 908

Change Cam Data Point Y (C02925) 908

Change of the basic function 380

Change Pos Data Point X (C02964) 911

Change Pos Data Point Y (C02965) 911

Changing cam data via parameterisation 564

Check configuration (C225) 760

Clock 840, 841

COB-ID 299

COB-ID EMCY (I-1014) 347

COB-ID SYNC message (I-1005) 343

Code number duplicated (error message) 677

Code refresh (error message) 632

Combination memory module/device not possible (error

message)

630

Combination MXI1/MXI2 not possible (error message) 629

Combination of module in MXI1/device not possible (error

message)

631

Combination of module in MXI2/device not possible (error

message)

631

Communication cycle period (I-1006) 344

Communication error between device and device module (error

message)

664

Communication task

Standstill > 3 s (error message)

681

Communication with module in MXI1 interrupted (error

message)

664

Communication with module in MXI2 interrupted (error

message)

665

Communication with safety module interrupted (error

message)

682

Config. analog input 1 (C00034) 735

Configure exception handling 290

ConnectTable active (error message) 675

Consumer heartbeat time (I-1016) 348

Cont Data Point Choice (C02943) 910

Cont Pos X0 (C02944) 910

Cont Pos X1 (C02945) 910

Cont Time (C02946) 910

Cont Track Choice (C02940) 909

Cont Type (C02941) 909

Control card

Supply voltage (24 V DC) too low (error message)

640

Control card is defect (error message) 624, 626

Control card is defect (UB18 neg.) (error message) 646

Control card is defect (UB24) (error message) 646

Control card is defect (UB8) (error message) 646

Control card is defect (VCC15 neg.) (error message) 646

Control card is defect (VCC15) (error message) 646

Control card is defect (VCC5) (error message) 647

Control card is incompatible (error message) 627

Control mode (C02567) 858

Control of two motor brakes 551

Controlled operation (without feedback) 407

Controller

Clamp operation (error message)

662

Overload during acceleration phases (error message) 658

Pulse inhibit is active (error message) 641

Controller enabled (error message) 641

Controller in STO state (error message) 641

Controller inhibit by (source) (C00158) 750

Correction of the leakage inductance 201

Counter

Brake chopper overload (C01203)

839

DC bus overvoltage (C01205) 839

Heatsink overtemp. (C01208) 839

Housing overtemp. (C01209) 839

Internal (C01210) 840

Ixt overload (C01204) 839

Mains switching (C01206) 839

Power section overload (C01212) 840

CPU

Overtemperature (error message)

643

Temperature > C00126 (error message) 642

Thermal detector is defect (error message) 644

CPU temp. warning threshold (C00126) 745

CPU temperature (C00069) 738

Curr. control par. of C75 C76 (C2866) 903

Current (C02773) 892

Current contr. reset time (C00076) 739

Current controller gain (C00075) 739

Current setpoint filter 150

Cycle (C02536) 853

Cyclic task

Standstill > 60 s (error message)

681

1 2 ... 931 932 933 934 935 936 937 938 939 940 941 ... 953 954

Comentários a estes Manuais

Sem comentários